- ARDUINO USB HOST SHIELD LIB HOW TO
- ARDUINO USB HOST SHIELD LIB INSTALL
- ARDUINO USB HOST SHIELD LIB SERIAL
- ARDUINO USB HOST SHIELD LIB MANUAL
The Bluetooth HID library allows you to connect HID devices via Bluetooth to the USB Host Shield.Ĭurrently HID mice and keyboards are supported. The BTD library also makes it possible to use multiple services at once, the following example sketch is an example of this: Some different examples can be found in the example directory.
ARDUINO USB HOST SHIELD LIB SERIAL
This library make it easy to add support for different Bluetooth services like a PS3 or a Wii controller or SPP which is a virtual serial port via Bluetooth. The BTD library is a general purpose library for an ordinary Bluetooth dongle. Simply set the corresponding value to 1 instead of 0. If you are using Arduino 1.5.5 or newer there is no need to activate the Arduino Mega ADK manually.The following boards need to be activated manually in settings.h: GPIO5 : SS, GPIO17 : INT, GPIO18 : SCK, GPIO19 : MISO, GPIO23 : MOSI.ESP32 is supported using the arduino-esp32.GPIO6 to 11 is also NOT usable, as they are used to connect SPI flash chip and it is used for storing the executable binary content.For example, reset the SoC itself from sleep mode. GPIO16 is NOT usable, as it will be used for some other purposes.Note it uses pin 15 and 5 for SS and INT respectively.ESP8266 is supported using the ESP8266 Arduino core.
Take a look at the following example code.
ARDUINO USB HOST SHIELD LIB MANUAL
See the "Interface modifications" section in the hardware manual for more information. Note that the Intel Galileo uses pin 2 and 3 as INT and SS pin respectively by default, so some modifications to the shield are needed.Arduino Due, Intel Galileo, Intel Galileo 2, and Intel Edison.All official Arduino AVR boards (Uno, Duemilanove, Mega, Mega 2560, Mega ADK, Leonardo etc.).To turn it on simply change ENABLE_UHS_DEBUGGING to 1 in settings.h like so:Ĭurrently the following boards are supported by the library: Enable debuggingīy default serial debugging is disabled.
ARDUINO USB HOST SHIELD LIB HOW TO
How to use the library Documentationĭocumentation for the library can be found at the following link. Now you should be able to go open all the examples codes by navigating to "File>Examples>USB_Host_Shield_20" and then select the example you will like to open.įor more information visit the following sites: and. The final structure should look like this: Now move the "USB_Host_Shield_20" directory to the "libraries" directory. Open that directory and create a directory called "libraries" inside that directory. There you will see the location of your sketchbook. Now open up the Arduino IDE and open "File>Preferences". Then uncompress the zip folder and rename the directory to "USB_Host_Shield_20", as any special characters are not supported by the Arduino IDE. Manual installationįirst download the library by clicking on the following link. Please see the following page for instructions.
ARDUINO USB HOST SHIELD LIB INSTALL
How to include the library Arduino Library Managerįirst install Arduino IDE version 1.6.2 or newer, then simply use the Arduino Library Manager to install the library. Aran Vink - Developer of the amBX library.Yuuichi Akagawa - Developer of the MIDI library.Andrew Kroll - Major contributor to mass storage code.Kristian Sloth Lauszus - Developer of the BTD, BTHID, SPP, PS5, PS4, PS3, Wii, Switch Pro, Xbox, and PSBuzz libraries.Oleg Mazurov - Alexei Glushchenko - Developers of the USB Core, HID, FTDI, ADK, ACM, and PL2303 libraries.įor more information about the hardware see the Hardware Manual. The shield can be purchased from TKJ Electronics. This is Revision 2.0 of MAX3421E-based USB Host Shield Library for AVR's. The code is released under the GNU General Public License.